18W Audio Amplifier | Schematic Diagrams


Schematic Diagrams

Useful schematic and wiring diagrams. ✔ ✔ Enjoy electronic circuits, let your idea comes to hardware

18W Audio Amplifier

]]>

circuit diagram

Amplifier parts:
P1 = 22K Log.Potentiometer (Dual-gang for stereo)
R1 = 1K 1/4W Resistor
R2 = 4K7 1/4W Resistor
R3 = 100R 1/4W Resistor
R4 = 4K7 1/4W Resistor
R5 = 82K 1/4W Resistor
R6 = 10R 1/2W Resistor
R7 = R22 4W Resistor (wire wound)
R8 = 1K 1/2W Trimmer Cermet (optional)
C1 = 470nF 63V Polyester Capacitor
C2,C5 = 100uF 3V Tantalum bead Capacitors
C3,C4 = 470uF 25V Electrolytic Capacitors
C6 = 100nF 63V Polyester Capacitor
D1 = 1N4148 75V 150mA Diode
IC1 = TLE2141C Low noise,high voltage,high slew-rate Op-amp
Q1 = BC182 50V 100mA NPN Transistor
Q2 = BC212 50V 100mA PNP Transistor
Q3 = TIP42A 60V 6A PNP Transistor
Q4 = TIP41A 60V 6A NPN Transistor
J1 RCA audio input socket

Power supply parts:
R9 = 2K2 1/4W Resistor
C7,C8 = 4700uF 25V Electrolytic Capacitors
D2 100V 4A Diode bridge
D3 5mm. Red LED
T1 220V Primary, 15 + 15V Secondary 50VA Mains transformer
PL1 Male Mains plug
SW1 SPST Mains switch

Notes:
Can be directly connected to CD players, tuners and tape recorders.
Don’t exceed 23 + 23V supply.
Q3 and Q4 must be mounted on heat sink.
D1 must be in thermal contact with Q1.
Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
Adjust R3 to read a current between 20 to 30 mA with no input signal.
To facilitate current setting add R8 (optional).
A correct grounding is very important to eliminate hum and ground loops. Connect in the same point the ground sides of J1, P1, C2, C3 &C4. Connect C6 at the output ground.
Then connect separately the input and output grounds at the power supply ground.

Technical data:
Output power: 18 Watt RMS @ 8 Ohm (1KHz sine wave)
Sensitivity: 150mV input for 18W output
Frequency response: 30Hz to 20KHz -1dB
Total harmonic distortion @ 1KHz: 0.1W 0.02% 1W 0.01% 5W 0.01% 10W 0.03%
Total harmonic distortion @10KHz: 0.1W 0.04% 1W 0.05% 5W 0.06% 10W 0.15%
Unconditionally stable on capacitive loads

author:
e-mail:
web site: http://www.redcircuits.com/

Most Wanted Diagrams:

More diagrams like 18W Audio Amplifier

How to build 18watt Audio Amplifier

How to build 18watt Audio Amplifier

How to build 10W Audio Amplifier with Bass-boost

How to build 10W Audio Amplifier with Bass-boost

18W Audio Amplifier

18W Audio Amplifier

Headphone Amplifier

Headphone Amplifier

]]>

Comments are currently closed.

Sponsored Link

    ]]>

Most view diagrams

Categories

Schematic Search

BatteryBlower motorBuickCadillacChevroletCigar LighterCircuit DiagramDodgeelectrical circuitElectrical SchematicElectrical SystemFordFuel PumpFuel Pump Relayfusefuse blockfuse boxFuse Holderfuse layoutfuse mapfuse panelGMCHeadlampHeaterHondaHornHorn RelayIgnition coilIgnition switchInstrument ClusterInstrument panelOldsmobilePontiacPower WindowRadioRelayschematic diagramStarter RelayStop LampStudebakerTurn SignalWiperWiring Diagrawiring diagramWiring Harnes

Schematic Diagrams

Powered by WordPress. Designed by SuperSidor. Schematic Diagram

Recent Posts