Useful schematic and wiring diagrams. ✔ ✔ Enjoy electronic circuits, let your idea comes to hardware
It was five years ago when I did an attempt to build my first fm-transmitter. It ended in a giant faillure. The only thing it did was interferring with our tv-set. Looking back it was due to the lack of information I had. A schematic was my only help. Now, five years later, I know a lot more about electro-technics. So I searched for a schematic of a stable, tested fm-transmitter with a far reach. I will put all information you’ll have to know in my page. I made drawings to make things clearer. As said before: I’m still building it, so I will add information every time I made progress. It would be wise for you out there not to start building untill I’m ready and have tested it. It has been succesfully built before, but my succes will give you a double security. I remind you of the fact that I can also fail.
Building a good fm-transmitter(88-110Mhz) begins with getting a good schematic. You don’t have to understand the precise working of the transmitter to build it. But some basic information won’t harm. A transmitter alone is, as you probably know, is not enough to start your radio-station. In the simplest form you need 4 things. First an input device such as an amplifiler you also use with your home-stereo.
You can also use a walkman. Details about input-devices in the page: “Input”. Second you need a regulated power-supply. In this case a 14-18 Volts/2,5-3,5 Ampere. One of the most influencial things you need is antenna and coax-cable. More about this later on. And finally the transmitter itself. You can devide the transmitter in two main parts: the oscilator and the amplifiler. The oscilator converts electric sound information into electromagnetic waves. The amplifiler gives these waves
a bigger amplitude.
It’s stable and has output of 15-18 watts. This enough to terrorize your wide surroundings at the fm-band.
The most often used technique to connect the components to each other is soldering them on a double sided copper-board. Another way is connecting the components floating. It is cheaper but very tricky. Below you see the copper-board layout(PCB). I designed it looking closely at the root scheme.
To get this pattern in copper surface you use a acid bath. Use a water-resistant permanent marker to paint your own copper-board black in the pattern the shown above. Color the back side ompletely black. The grid-squares are 0,5*0,5 cm each.
When the acid has eaten the non-painted copper away you must remove the complet thin layer of black paint with sandpaper. Don’t remove too much copper with it.
So, now you have the surface to solder the electric components on.
Now a few basic rules for good soldering:
1. Use a special electronics-solderingrod with a slim top.
2. Use soldering-metal with an anti-oxidant-fluid core.
3. Don’t heat the components! Heat the connection-point on your PCB.
4. Make sure that the surface is not too smooth.
5. Don’t use too much metal.
6. Don’t let the soldering metal form a bridge beetween two copper-surfaces.
7. If you’re smart you start from the middle of your prepaired board.
In this way you’ll have enough space.
Below the schematic. The yellow lines are pieces of copperboard that devide the transmitter in 3 parts. This is essential. Without them, internal interferrence will ruin your signal.
There are some components that need extra attention. Transistors usually have 3 or 4 different
wires comin’ out. If you connect these wires in the wrong way the transmitter won’t work. It may even explode. The picture below shows how to prevent from such an event.
You can find the numbers and letters back in the soldering schematic.
Coils also require extra attention. You can buy the coils trough ferrite in the shop, but the other ones have to be made yourself. Use 1mm AgCu wire. A coil like 7x/d=10mm/l=15mm, goes round 7 times, has an diameter of 10 millimeter and is long 15 millimeters. The best way to make a coil is to bend it around a pencil or other cilindrical shaped object tight. The diameter of the object is always d-coil minus 1 mm. In this case 9mm. As I said: bend the wire round (in this case 7times) with the revolves tight together. To get the desired length stretch the coil when still around the pencil
If you decide to build the transmitter and buy the parts, this list will be handy:
READ THIS E-MAIL I RECEIVED
just to give some input: I have built the 15W FM transmitter you describe about 4.5 years ago.
The PCB lay out and component selection is still the same as it was then and after some modifications, I had an average output power of 16.8W @ 98.6 MHz (measured with Rhode and Schwarz equipement). You will need additional filtering on the power lines otherwise a stable power supply for the modulating circuit cannot be guaranteed. The legs of the modulating diode are, at best, kept long for extra capacitance. This to make sure you fall within the FM band because before I did that, I had
problems falling withing the 88-108 MHz. I was actually interfering with the police and fire brigade radio bands (Belgium). Of course, this is not the intention. I also advice you and readers to carefully check the orientation of the BLY88 because my professor blew one up due to lack of specification and inclarities in the datasheets (the actual pin out of the component changed a few years ago, resulting in a swapped emitter and collector – no good if you position it wrong!!! (the white cap flies of)). You will also need to play with the spacing between the windings of the different coils in order to get a good coupling between the different stages. I short circuited parts of the coils and made them smaller than specified to have near-optimal coupling. I also added extra ferrite bead coils for extra decoupling of the power lines, and used a very good shielding. Above 16.8W there is coupling (primarily through the air) between the output and the modulating/input stage and oscillation occurs. So for I have not found any other solution than lower the output power. Both extra decoupling
and extra shielding had no effect (my transmitter is built into a fully closed aluminium box with seperating plates that are fully connected to the case or ground plane on the PCB, except from where tracks run (0.5mm spacing provided)). Also, use a good heat sink for the last power stage!!!
I hope this information will be usefull. If you have any questions, please ask.
Space applications and space instruments division
web site: http://www.geocities.com/SouthBeach/3433/transmit.htm
More diagrams like 15W Fm-transmitter
Comments are currently closed.
Most view diagrams
- 2001 Chevrolet Trailblazer Fuse Box Diagram
- The Astable-Oscillator Operating Mode in 555 Timer IC Circuit
- Infrared Detector
- 96 ford 350 Cube Van 7 Fuse Box Diagram
- 1994 Honda Magna VF750C Electrical Wiring Diagram
- How to build 220 Volts Flashing Lamps
- Fog Light Wiring Diagram For 1953 Studebaker Champion And Commander
- Wiring Diagrams Of 1962 Chevrolet Corvette
- Miniature Loop Alarm
- DC motor controller diagram with SCR and cmos ic
- Amplifier Diagrams
- Automotive Diagrams
- Car Fusebox Diagrams
- Circuit Diagrams
- Electronic Projects
- Inverter Diagrams
- Power Supply Diagrams
BatteryBlower motorBuickCadillacChevroletCigar LighterCircuit DiagramDodgeelectrical circuitElectrical SchematicElectrical SystemFordFuel PumpFuel Pump Relayfusefuse blockfuse boxFuse Holderfuse layoutfuse mapfuse panelGMCHeadlampHeaterHondaHornHorn RelayIgnition coilIgnition switchInstrument ClusterInstrument panelOldsmobilePontiacPower WindowRadioRelayschematic diagramStarter RelayStop LampStudebakerTurn SignalWiperWiring Diagrawiring diagramWiring Harnes