Schematic Diagrams

Useful schematic and wiring diagrams. ✔ ✔ Enjoy electronic circuits, let your idea comes to hardware


High Efficiency Switch Mode 3.3A 10A Regulator

This switch mode regulator circuit has higher current output than  our previous switch mode regulator, but it uses same controller IC. Up to 10A can be served by this switch mode regulator. The output of this regulator circuit is regulated at 3.3 volt, and the input range is 4-9Volt. The SHDN pin can be pulled […]


High Efficiency Switch Mode 3.3V 5A Step-Down Converter

This switch mode step-down converter has very good efficiency, up to 94% can be obtained. This switch mode regulator uses LTC1266-3.3 controller with external N-Channel power mosfet, and need only a 5uH inductor because it uses high frequency switching. Here is the schematic diagram of this switch mode step down converter circuit: To optimize efficiency, […]


Transformerless, Switch Mode Boost Regulator, A Step-Up Converter

Using this switch mode regulator circuit, you can get a stable 12 volt output (500mA) although you just have 4,3 – 10V power supply. You can even boost a 3.5V input to 12V if the load draws only 100 mA or less. This switch mode voltage regulator use LTC1266 IC chip from Linear Technology. Here […]


Constant Current Constant Voltage SMPS (Switch Mode Power Supply)

This constant current constant voltage  SMPS can be used to efficiently charge a battery. This circuit gives 7.2V at constant voltage mode, and 600 mA at constant current mode. Here is the schematic diagram of the circuit: The mechanism is simple, when the load impedance is high, then the output voltage will be constant at […]

Miniature Voltage Isolation Provides Positive and Negative Supply

The development of miniature low-power (<2-W) DC/DC converters is growing rapidly because of the hot growth in distributed-power architecture. This application minimize the converter’s impact onboard space. This device is very useful for safety-critical applications such as medical equipment, and telecommunications, and industrial applications because it provides point-of-use isolated power conversion for analog circuitry. In […]


Versatile Boost Converter with TPS6108x

There are two types of highly integrated boost converters, the TPS61081 and  TPS61080.  Both of them require low input voltage of 2.5V and the output is adjustable up to 27 V. The TPS61080′s current limit rating of the integrated power switches is 0.5 A and 1.3 A for TPS61081. Here is the circuit : It […]


TPS108x Versatile Boost Converter

This is Versatile Boost Converter circuit using TPS108x. The TPS1081 has chosen because it is suitable for application that requires up to 20 V and 100 mA to drive each column of a passive-matrix OLED (PMOLED). the TPS61080 is suitable for application that requires less than 10 V and only tens of milliamps per column […]


450W Power Factor Controller with Universal Input Voltage Range

This power factor controller accept voltage from 90 to 268 Vac,  that’s why we call it power factor controller with universal input, since any standards of mains supply  in almost any country would fall within that range. This power factor controller is capable of handling up to 450W load. Here is the schematic diagram of […]


52W SMPS AC-DC Adapter

One AC-DC converter that provides a good accuracy is SMPS AC-DC converter. Test data shows efficiency of 85.4% at 230 Vac input and 6A output current and 83.2% at 115 Vac input and 6A output current. This converter has the universal input voltage range. containing 92 to 276 Vac variation with only 24 mV change […]

Step-Down Charge Pump Regulator for USB Powered Devices

this is a circuit of Step-Down Charge Pump Regulator for USB Powered Devices. The critical design parameter of this circuit is the circuit area. To solve this problem we can use Charge pump step-down circuit. This circuit only requires   the charge pump controller and  four ceramic capacitors. So it is a low cost circuit because […]

Previous Posts